HummingBoard Pro & RZ/V2L SOM Quick Start Guide

Introduction

The following quick start guide provides background information about the HummingBoard Pro RZ/V2L.

The guide will give a technical overview about the product and by the end of it you should be able to boot an operating system and begin testing your application.

Revision and Notes

Hardware Setup

Product specifications

Block Diagram

The following figure describes the RZ/G2L Block Diagram.

Open

Visual features overview

Please see below the features overview of the connector side of the HummingBoard Pro & RZ/V2L SOM.

Open

Print side connector overview of the HummingBoard Pro & RZ/V2L SOM.

Software Setup

Cable setup and prerequisites

Here is what you will need to power up and use the board:

• Linux or Windows PC

• HummingBoard Pro with RZ/G2L SOM (HummingBoard Pro & RZ/V2L SOM)

• 12V Power adapter (HummingBoard Extended has wide range input of 7V-36V, it is recommended to use 12V power adapter).

• Micro USB to USB for console, the HummingBoard Extended has an onboard FTDI chip.

• IP router or IP switch

• USB Disk and SD Card

Boot Select

Before powering up the board for the first time it is recommended to select the boot media. In order to configure the boot media, please refer to HummingBoard RZ/V2L Boot Select .

Generating Yocto, Buildroot and Debian image

Yocto

1. Clone the repository from the “List of supported OS” link and move your terminal to this directory.

2. Download the layers by this command

   $ repo init -u https://github.com/SolidRun/meta-solidrun-arm-rzg2lc.git -b dunfell -m meta-solidrun-arm-rzg2lc.xml $ repo sync

3. In this stage you can modify your image configs as you want, you can find more info about it the the repository.

4. For graphics support you need to explore in the readme file in the github and follow the instructions of this utility.

5. Set the environment of the image that going to be build by this command

   $ TEMPLATECONF=$PWD/meta-solidrun-arm-rzg2lc/docs/template/conf/rzg2lc-solidrun source poky/oe-init-build-env build

6. Build your own Yocto image by this command

   $ MACHINE=rzv2l-hummingboard bitbake <target>

   • NOTE: Choose your relevant target, for example:
     -core-image-bsp: cli image.
     -core-image-weston: graphical image.
     -core-image-qt: graphical image including qt.

Buildroot/Debian

1. Clone the repository from the “List of supported OS” link and move your terminal to this directory.

2. In this stage you can modify your image configs as you want, you can find more info about it the the repository.

3. Build your own image by this command

Booting from SD card

The following shows how to set the switches on the boot source selector:

Once you set the switches, you can apply the following for booting from SD card:

1. Downloading the image
   Download the image (for example Debian) by running the following command on your Linux/Windows PC:

   • For more Debian releases, please visit Debian Releases for RZ/V2L.

2. Writing the image to the SD card
   Use the following commands for writing the image to an SD card:

   • For more information, please visit Flashing an SD Card .

   • Note: Plug a micro SD into your Linux PC, the following assumes that the USB-Disk / Micro-SD is added as /dev/sdX and all it’s partitions are unmounted.

3. SD card insertion
   Please Insert the SD card into your device.

4. Power connection
   Connect your power adaptor to the DC jack, and then connect the adaptor to mains supply.

5. Power On
   Hold on the On/Off Power button - SW1 (as shown in the figure below)

   • Note: The system should turn on by default when the power is connected (without pressing the button).

6. Serial Connection
   Please insert the micro USB into your device, then you can refer to Serial Connection for installing necessary serial connection software in Linux/Windows.

• In order to be able to log in , please insert “root” as a username as follows:
  
  

Final stages

The following stages need to be done in order to finalise the imaging:

1. Run fdisk /dev/mmcblk0 if using SD or eMMC.

2. Recreate the rootfs partition (mostly the second partition) by deleting it and then creating a new partition that starts at the next sector after the first one and extends to the end of the drive (or less depending on your needs).

3. Write the new partition, when prompt about ‘Do you want to remove the signature?’ then answer with Yes.

4. Run resize2fs /dev/mmcblk0p2 if using SD Card or eMMC.

5. In this stage the root partition should be big enough to start populating it; but first update the RTC clock.

6. Connect the RJ45 to your network with internet access (and DHCP server); and then run dhclient.

7. Update the RTC clock by running ntpdate pool.ntp.org and then hwclock -w.

8. Run apt-update commands below and then populate the root filesystem as you wish.

Here is an example of the same process in the rzg2lc device until the 3rd step (include):

After those steps you should end the process in this way (step 4 to the end):

In the end you should see with “lsblk” that the partition size is in the required size.

More Features

List Of Supported OS

Build from source

• GitHub - SolidRun/build_rzg2lc: Scripts to build basic Buildroot/Debian images for RZ/{G2LC, G2L, V2L} based platforms

Documentation

Related Articles