HummingBoard Pulse & i.MX8M Quad SOM Quick Start Guide
- Kareiman Fadly (Unlicensed)
- SolidRun
Introduction
The following quick start guide provides background information about the HummingBoard Pulse.
The guide will give a technical overview about the product and by the end of it you should be able to boot an operating system and begin testing your application.
Revision and Notes
Date | Owner | Revision | Notes |
|---|---|---|---|
Oct 28, 2021 |
| 1.0 | Initial release |
Table of Contents | |||
Hardware Setup
Product specifications
Model | HummingBoard Pulse |
|---|---|
SOM Model | NXP i.MX8M Dual / Quad core Arm Cortex A53 up to 1.5GHz (with Arm M4 GPP) NXP i.MX8M Mini Single to Quad core Arm Cortex A53 up to 1.8GHz (with Arm M4 GPP) |
Memory & Storage | Up to 4GB LPDDR4 |
Network | 2 x RJ45 |
Connectivity | 2 x USB 3.0 * |
Media | HDMI 2.0 out ** Onboard audio codec |
I/O | 1 x Reset button |
OS Support | Linux |
Environment | Commercial: Industrial: Humidity (non-condensing): 10% – 90% |
Dimensions | Board: 102mm x 69mm |
Power | 7V – 28V wide range |
Enclosure | Optional extruded aluminum (IP32) enclosure |
|
Supported with i.MX8M SOM. For more detailed information about our SOM-i.MX8M series please visit this user manual : i.MX8M SOM .
Please note
(*) Only USB 2.0 supported with the i.MX8M Mini SoC.
(**) Only supported with the i.MX8M SoC.
(***) Only 1 x MIPI-CSI supported with the i.MX8M Mini SoC.
Block Diagram
The following figure describes the i.MX8M Block Diagram.
Visual features overview
Please see below the features overview of the connector side of the HummingBoard Pulse.
Print side connector overview of the HummingBoard Pulse.
Software Setup
Cable setup and prerequisites
Here is what you will need to power up and use the board:
Linux or Windows PC
HummingBoard Pulse with SOM
12V Power adapter (HummingBoard Pulse has wide range input of 7V-28V), alternatively you can use a PoE injector to power on the device.
Micro USB to USB for console, the HummingBoard Pulse has an onboard FTDI chip.
IP router or IP switch
Boot Select
Before powering up the board for the first time it is recommended to select the boot media. In order to configure the boot media, please refer to HummingBoard Pulse and Ripple Boot Select .
Booting from SD card
The following shows how to set the switches on the boot source selector:
Please Note:
The black rectangle represents the switch position.
Once you set the switches, you can apply the following for booting from SD card:
1. Downloading the Debian image
wget https://solid-run-images.sos-de-fra-1.exo.io/IMX8/Debian/sr-imx8-debian-bullseye-20201020-cli-imx8mq-sdhc-hummingboard-pulse.img.xzFor more Debian releases, please visit Debian Release for i.MX8.
2. Writing the image to the SD card
Use the following commands for writing the image to an SD card:
xz -dc sr-imx8-debian-bullseye-20201020-cli-imx8mq-sdhc-hummingboard-pulse.img.xz | dd of=/dev/sdX bs=4k conv=fdatasyncFor more information, please visit Flashing an SD card.
3. SD card insertion
Please Insert the SD card into your device.
4. Power connection
Connect your power adaptor to the DC jack, and then connect the adaptor to mains supply.
5. Serial Connection
Please insert the micro USB into your device, then you can refer to Serial Connection for installing necessary serial connection software in Linux/Windows.
Once you installed the necessary serial connection software, you should be able to see the following:
In order to be able to log in , please insert “debian” as a username and password as follows:
More Features
Internet
Connect an Ethernet cable to your HummingBoard Pulse (for internet access during boot-up).
Models HummingBoard with WiFi, can be connected via WiFi or wired Ethernet.
Please check you Ethernet connection.
Use the following commands in order to keep your system up-to-date:
apt-get update
apt-get upgrade
rebootFor more detailed information, please refer to i.MX8M Debian .
WiFi
You can connect to WiFi using any application, such as : connmanctl or wpa_spplicant.
An example for connecting to WiFi using wpa_supplicant:
1. To bring a WiFi interface up, run the following :
2. Install the wpa_supplicant package:
3. Edit network interfaces file :
At the bottom of the file, add the following lines to allow wlan as a network connection:
4. Create a configuration file with the relevant ssid:
5. Make sure it works:
Restart your device and it should connect to the wireless network. If it doesn't, repeat above steps or get help from an adult.
For more information about using wpa_supplicant , you can refer to wpa_supplicant or wpa_supplicant.
Bluetooth
For Building Newt Nimble BLEHCI firmware, you can follow this page Building Newt Nimble BLEHCI firmware for the iMX8MQ NINA-B1 Module .
Cellular Modem
The cellular modem is a more fully featured extension of which contains a cellular module with additional hardware interfaces and a SIM card slot.
You can connect your cellular modem to the mPCIe, and insert a SIM card.
For some cellular modules to be connected, please refer to Cellular Modules .
List Of Supported OS
Build from source
Documentation
Related Articles
Related pages
SolidRun Ltd.