Content Comparison

Revision and Notes

Introduction

The following quick start guide provides background information about the CuBox-i.

The guide will give a technical overview about the product and by the end of it you should be able to boot an operating system and begin testing your application.

Hardware Setup

Product Specifications

Block Diagram

The following figure describes the i.MX6 Block Diagram.

Visual features overview

• A demonstration of how to connect your cables and other peripherals to your CuBox-i can be found here : How to connect cables and peripherals to your CuBox-i

Software Setup

Cable setup and prerequisites

• Micro USB cable

• Power supplier : regulated 5V supply with 2A source capacity (3A for CuBox-i4pro)

• Micro SD card

• Linux or Windows PC

• Router or switch with Ethernet cable

Booting form an SD card

1. Downloading the Yocto image

Download the Debian Yocto image by running the following command on your Linux/Windows PC:

wget https://images.solid-run.com/IMX6/meta-solidrun-arm-imx6/2024-07-05_ab67695/core-image-weston-sdk-imx6qdlcubox.wic.gz

• For other software releases, please visit images.solid-run.com/IMX6.

2. Writing the image to the SD card

Use the following commands for writing the image to an SD card:

gzip -dc core-image-weston-sdk-imx6qdlcubox.wic.gz | dd of=/dev/sdX bs=4M conv=fsync

• For more information, please visit Flashing an SD Card .

3. SD card insertion

Please Insert the SD card into your device.

4. Power connection

Connect your power adaptor to the DC jack, and then connect the adaptor to mains supply.

5. Serial Connection

Please insert the micro USB into your device, then you can refer to Serial Connection for installing necessary serial connection software in Linux/Windows.

Once you installed the necessary serial connection software, you should be able to see a log-in prompt similar to the following:

• In order to be able to log in , please insert “root” as a username, password is empty:

More Features

Internet

If you have purchased CuBox-i1 or CuBox-i2 first connect an Ethernet cable to your CuBox-i (for internet access during boot-up). Models CuBox-i2ex and CuBox-i4Pro (Or CuBox i1 / i2 with WiFi function), can be connected via Wi-Fi or wired Ethernet.

• Please check you Ethernet connection.

Wi-fi

• You can connect to WiFi using any application, such as : connmanctl or wpa_spplicant

• TLDR Connecting to WiFi network using connman:

  Code Block

  root@imx6qdlcubox:~# connmanctl connmanctl> enable wifi Enabled wifi connmanctl> scan wifi Scan completed for wifi connmanctl> services Vodafone Hotspot wifi_10cea9c83c04_566f6461666f6e6520486f7473706f74_managed_none Vodafone-guest wifi_10cea9c83c04_566f6461666f6e652d6775657374_managed_psk ... connmanctl> agent on Agent registered connmanctl> connect wifi_10cea9c83c04_566f6461666f6e652d6775657374_managed_psk Agent RequestInput wifi_10cea9c83c04_566f6461666f6e652d6775657374_managed_psk Passphrase = [ Type=psk, Requirement=mandatory ] Passphrase? super-secret-pw Connected wifi_10cea9c83c04_566f6461666f6e652d6775657374_managed_psk connmanctl> quit root@imx6qdlcubox:~# ping google.com PING google.com (216.58.206.46): 56 data bytes 64 bytes from 216.58.206.46: seq=0 ttl=118 time=13.097 ms ...

Bluetooth

1. For showing all Bluetooth devices, run the following:

hciconfig -a

2. Choose a device, and turn it on:

rfkill unblock bluetooth
hciconfig hci0 up

3.Set up the Bluetooth name:

hciconfig hci0 name 'SolidRun_Ble'

4. Make your Bluetooth detectable by other devices:

hciconfig hci0 piscan

5. If you want to connect to other devices:

• Start by scanning for other Bluetooth devices:

hcitool scan

• Choose a MAC address and connect :

rfcomm connect 0  $MAC 10 & 

• You can check the communication between the devices by writing :

l2ping -c 4  $MAC

List Of Supported OS

OS
	i.MX6 Debian
	Yocto for i.MX6
	i.MX6 Archlinux
	XBian for i.MX6

Build U-Boot & Kernel from sources

• Build a Linux kernel -  i.MX6 Kernel

• Build a U-Boot - i.MX6 U-Boot

Documentation

Related Articles